Silverside Beef Roast - tough to cut on the plate and chewy

Silverside Beef Roast - tough to cut on the plate and chewy - Ethnic male cook cutting roasted duck

I recently roasted a Silverside joint for a typical English Sunday dinner.

It was a pretty standard job. I got it to room temperature, rubbed it with salt and pepper and give that an hour to mesh. After that I seared all side in a cast iron pan, lifted it on a trivet of carrot, celery, garlic & onion and cooked it at 180C (electric fan) until the middle reached my desired temperature, in this case 50C rising to 62C when resting (20/30mins) - came out medium rare.

...anyway, the issue is that after slicing it and plating it up, it was still pretty difficult to cut on your plate - although it had tones for flavour and was very 'juicy'.

I did experiment slicing it more thinly and that did help a bit - but it can of seem rather odd to be eating ultra thin sliced beef.

We used to eat Silverside all the time when I was a kid and I don't remember it being this bad, but then again my parents would have cooked the crap out of it and it was probably pretty dry.

So is this just how Silverside is? (and presumably topside) and I should by a more premium cut (like Sirloin joint) if I want to it to cut more easily or am I missing a trick - do I need to buy a better quality (from a good butcher)/longer aged joint?



Best Answer

Silverside is one of those cuts that varies a lot, I've had topsides and silversides that came out reasonably tender and juicy, and I've had ones where I need power tools to cut them, even when I do everything right. They're cuts I avoid as a result.

Silverside is a cut that comes from the rear of the animal, it doesn't have much marbling and does a fair amount of work, so has lots of connective tissue which toughens it. Cattle breed and how the animal was raised make a big difference in whether you'll get a good result. If you do want to buy it then be selective, look across the cuts the supermarket has for marbling. Stick a thumb into them to see which one is most tender, and pick that.

Tweaking your method would help you get a better result. 180C fan is too hot, you will overcook the outside before the middle is done, and you will have less time for connective tissue to break down and make the result tender. I like to start mine hot to get a good crust, but after 10 minutes I would turn it down to 150C at the highest, 140C would be even better. Next you need to rest it for much longer than 20 minutes. When you rest the meat it continues cooking, connective tissue keeps breaking down, and the meat relaxes. This takes time, especially for tougher cuts. Some professional chefs say you should rest it as long as you cook it, I'm not in that camp myself but I'd say wrap it tightly and give it at least an hour before you cut it.




Pictures about "Silverside Beef Roast - tough to cut on the plate and chewy"

Silverside Beef Roast - tough to cut on the plate and chewy - Crop man cutting cutlet on plate with salad and potatoes
Silverside Beef Roast - tough to cut on the plate and chewy - Delicious burger with vegetables and fries
Silverside Beef Roast - tough to cut on the plate and chewy - Delicious burger with juicy cutlet lettuce an onions cut into quarters served on white plate and placed on wooden table in kitchen against blurred background



Why is my silverside beef chewy?

If cooked for a long time on low heat in an oven without any preparation, the meat will become incredibly chewy and tough. It is important to cover the roast completely with foil or a lid, leaving only a few areas open so excess steam can escape. This will help to keep moisture near the meat so it does not dry out.

Why is my roast beef so chewy?

Leaner roasts such as rump, chuck, or brisket have less fat marbling, so they can become chewy if not cooked correctly. It is the fat and connective tissue in the roast that is softened by long, slow cooking to produce flavor and tenderness.

Is silverside a tough meat?

Silverside beef is a roasting joint that comes from between the rump and hind leg of the cow. The silvery covering on its membrane surface gives its name. What is this? It's a relatively cheap cut of meat, which is very lean and, when cooked incorrectly, will be tough.

How do you fix a chewy beef roast?

Cut it up or shred it to use in a variety of recipes.
  • Try Beef Stroganoff. Put leftover roast beef to good use and make slow cooker beef stroganoff, as cooking tough meat slowly in liquid tenderizes the tough fibers. ...
  • Build Some Burritos. ...
  • Add to Ramen Noodles. ...
  • Leftover Roast Beef Stew.





  • More answers regarding silverside Beef Roast - tough to cut on the plate and chewy

    Answer 2

    If you want something as lean and generally tough as a silverside to come out reasonably tender and juicy, you'll need to alter your cooking method.

    I'd recommend using something similar to the High Temperature Eye of Round cooking method mentioned here:

    • Preheat to 500 degrees F
    • Put the roast in, drop to 475 degrees F
    • Roast for 7 minutes per pound
    • Turn off the oven, and leave it closed to gradually coast down the temperature for the next 2 to 2 and a half hours

    You might need to make some adjustments if using a fan-forced oven that vents oven heat quickly when turned off.

    Sources: Stack Exchange - This article follows the attribution requirements of Stack Exchange and is licensed under CC BY-SA 3.0.

    Images: Kheng Tang, Karolina Grabowska, Ryutaro Tsukata, Katerina Holmes