Why does my spinach pasta break when I run it through the cutter?
Why does my spinach pasta break when I run it through the cutter? Too dry? Need more gluten? Flour mix is half 00 and half semolina. Spinach is high-quality spinach powder.
Best Answer
In terms of the science of the dough, there are three probable culprits to consider:
Insufficient hydration. That is, your dough either doesn't have enough water (from any source, including for example, any eggs) to form a cohesive dough, or it has not rested long enough for the water to be absorbed into the starches of the flour.
The symptom for this is that the dough is in general crumbly and frangible, and doesn't want to hold together.
If this is the case, the remediation would be simple: add more water, and let the dough rest about 30 minutes.
Insufficient gluten development. Gluten is what gives pasta its strength. It needs both enough water (see issue number 1), and enough kneading to develop. You may need to knead your dough more.
If this is the case, knead by hand until it is cohesive enough to go through the rollers. The first rolls not only thin the dough, they continue to knead it, further developing the gluten.
The symptom for this is that it holds together when pressed, but not when worked, compared to the first issue.
Excessive interference. There may be too many other ingredients (such as the spinach powder) getting in the way of the gluten formation (see point number 2). They can physically impede the gluten from developing. You only want to add an accent of non-flour/water ingredients.
This would be the hardest case to recover from, as you essentialy would need a new recipe with a new balance. You could try making a second batch without the interfering agent, and combining them, but probably not worth the effort.
It is hard to tell if this is the case, versus number 2, unfortunately. If you are using a quality recipe, this is unlikely.
Pictures about "Why does my spinach pasta break when I run it through the cutter?"
Why is my pasta dough breaking apart?
So what causes pasta dough to tear and form holes when rolling? The primary reason is that the dough is not being rolled, folded and fed in properly on the correct settings of the pasta roller. If the dough is not flat enough, fed in at the wrong angle, or too fast through the roller, it can bunch up and rip.How do you keep pasta from crumbling?
If pasta dough is too dry, adding a small amount of water at a time to the dough will solve the problem of having dried dough. If the pasta has not formed a perfectly moist ball after adding a little water, then you can add a small amount of flour to the dough to help obtain your desired texture.What happens if you overwork pasta?
This is because kneading the dough too much will cause damage to the gluten molecules, which give it its elasticity. While it's practically impossible to overwork pasta dough if you're kneading it by hand, the same can't be said for when you use a bread machine to mix the dough.Why are my egg noodles Tough?
1) Too much flour or not enough Too much flour makes the pasta tough. Not enough will result in runny lumps that are impossible to roll through pasta maker.The One Spaghetti Rule You Should Never Break
More answers regarding why does my spinach pasta break when I run it through the cutter?
Answer 2
Not sure what spinach powder is...I typically make a fresh pasta dough with AP flour (though 00 is good too) and eggs. Put 3- 4 c flour on a board, create a well, crack in 3-4 eggs, mix, then knead (remove excess flour...or add more as necessary). When adding spinach, I use frozen that has been thawed and run through a food processor or blender, then placed in a towel to squeeze out as much moisture as possible. Add this to the well with the egg (a 6-8 ounce frozen package). The key here is, once the dough comes together, to knead well for 10 - 15 minutes. The dough should not be sticky, so keep dusting with flour until it is fairly stiff. Then wrap in plastic and let rest for at least 30 minutes. Cut off a piece to roll and run it through the roller. Dust with flour, fold in thirds and run it through (largest setting) again. Repeat 3 to 4 times making sure the dough is no too sticky. Proceed to thinner settings and desired shape.
Sources: Stack Exchange - This article follows the attribution requirements of Stack Exchange and is licensed under CC BY-SA 3.0.
Images: eberhard grossgasteiger, Ketut Subiyanto, Alex Green, Tatiana Syrikova