What characteristics should a bread peel have?

I know this question has been asked a long time ago, but as I have been shoving around 1000 loaves of breads in 2014 alone (we bake for charity), all in a traditional wood-fired oven like in the picture, I couldn't resist... The following points are geared towards wood-fired ovens, but are valid for most sizes, from the 8-loaves home versions to larger sizes. "My" oven can handle 100 pounds of dough / 50 loaves per session.

The Handle:

• Must be long enough to reach all the way in and be still long enough to get a good grip with two hands. You need leverage. So aim for [door to back corner] + at least 2 feet/60cm. This influences the place for your oven: You need at least as much space behind you, so that you can move freely. (Often overlooked in home environements...)
• Must be heat-proof, but non-conductive. This rules out metal, because even with gloves you'd be scorching your hands. Wood is a good choice. Use hardwood, round or rounded, make sure there are no splinters(!) (but use gloves, just to be sure). When placing multiple loaves, you will want to work fast in order to have roughly the same baking time for all of them and to loose as little heat as possible through the oven door. So basically you will be rather sliding the handle along your hands than using a hand-over-hand motion. Catching a spliter this way will hurt like h**l - check the handle regularly, e.g. after each baking session. This answers the question of detaching the peel part: your handle will be the longest part and should be in one piece. So a removable peel doesn't change this much. If you want to fix it with some kind of nuts and bolts construction, do it horizontally, making sure nothing sticks out at the bottom and no cavity gets filled with ash, preventing disassembly.

The Peel

• Choose a size that fits your baking habits: Estimate the usual loaf size(s), determine the required peel size from there: I'd add at least 2 in / 5 cm to the largest meassurement and use tis to determine the diameter or side length of the square /see later). Same goes for pizza: The entire pizza must fit on the peel. For cakes, the tin or sheet should provide enough stability, and you might choose to simply place it at the front of the oven and then use the peel to gently push it in place (more on this later). But don't overdo it: The larger the peel, the more unwieldy. Do not include French Bread / Baguette in this calculation, get a special sword-shaped peel for them.

• Use warp-free material. This may be metal (but some do warp, I'm no expert, ask a professinal before building your own), but wood is fine. It will not burn or scorch if handeled properly. Stay clear from plywood, its likely to warp, splinter and if too thin can't hold a larger loaf well. Also, there's the question of glue: food grade, yes, but appropriate at high heat? I'd by wary... Most peels I have worked with are solid wood, but composed of three equally wide strips, glued together (no idea on the glue used), running in the same direction as the handle. I strongly suppose this is to reduce warping, at least that's what my carpenter suggested.

• Shape is somewhat a matter of choice. If you are making mostly pizza, a round peel is good. Square peels can be impractical if you want to reach the back corners of the oven. My preferred peel is basically square(ish), with heavily rounded corners, the radius of the corners is probably 2in / 5cm. I can easily reach all corners of the oven without "catching" on the corners of the peel. (Sorry if this sounds muddled...)
  You do want a thin(ish) front edge, though, to slide easily under the bread / pizza / baking tin when removing them from the oven. For metal peels, this feature is obviously "included", for wooden peels, you can either just taper the front edge - like a knife - or taper the entire peel - the "wedge-shape" mentioned in the question. The latter would be my coice, because it allows the front edge to always/automatically be the lowest point without having to lift the handle much. You do not need a razor-sharp edge, somewhere around 2-5 mm is thin enough. You may get some wear over time as the stone of the oven sands the tip down. If the edge gets to "serrated" (after a few years), just sand it down a bit.
  There is one aspect of shape that is easily overlooked, though: The back side of the peel where it meets the handle. If you have a sharpish corner here, it can be used to pull a baking tin towards you, either from the side or from the top. Just "hook" the peel to the tin and pull gently. This is especially handy if you need to manouever multiple tins around because a back one is done before the front one. You can try to slide the peel underneath, but this can be tricky if a filling hasn't set yet or you are bumping the tin into something else.

• Maintenance: Neither type of peel should require maintenance. Brushing or wiping off excess ash and flour should be enough. Be generous with the dusting flour and you should "never" get stuck-on dough on the peel. If you do spill something, just wipe it off and let dry. No seasoning required or recommended.

Here is what Kenki Lopez says about the desirable qualities for peels, in the context of pizza, but pizza is just flat bread with stuff on top:

Serious Eats article on Best Pizza Peel for my home

The main take away is that wood is not recommended, due to being flammable, thick, and hard to clean--they like metal. I know that isn't what you want to hear when planning to make your own...

As for shape, a squared off front edge (as opposed to rounded), and a length to reach the back of your oven make a peel desirable.

In my home oven, I just use a plastic cutting board like this:

Mine have a larger hole in the handle, so I can easily pick one up wearing an oven mitt. I put cornmeal on the cutting board then put the loaf on it to rise, and slide it onto the preheated pizza stone really easily.

Advantages: they're lightweight, easy to clean, and I have about 8 of them already.

Disadvantages: no long handle, which would be more important if you were trying to put bread further into a hotter oven. For me it's not an issue, and if I ever feel that it is, I wear an oven mitt.