Fighting flash rust on cast iron pans

Fighting flash rust on cast iron pans - Tasty sausages in frying pan on table

I completely stripped the seasoning off of two pans with the intention to start the seasoning process over from scratch. One pan I had messed up the seasoning (skillet) and the other (sauce bowl) was on clearance because part of the seasoning was scratched and was an "easy" fix.

I used the oven cleaner method and finally got everything down to the bare metal. I went to wash everything off and did a vinegar rinse to neutralize the oven cleaner and rinsed everything in cold water.

Initially, I tried drying the pans in the oven before applying any Crisco to start the seasoning process, but the flash rust got to the pans first. I started completely over again from square one repeating the oven cleaner method. I had read that you can do a quick dry and apply your oil pretty much immediately then place the pans in the oven to dry at a lower temperature. Tried that and began the seasoning process by wiping off any excess oil and baked the pans at 450 deg for about 1 hr. After the pans had cooled, they came out looking brown, almost like flash rust stuck through the seasoning process as opposed to the beautiful iconic black everyone thinks of.

My question is - did I miss anything or do something wrong in this process? I had watched so many videos and read so many blogs and I thought I had followed along pretty well yet my results didn't match anyone else's.

Sauce bowl after attempt.

Skillet after attempted seasoning.



Best Answer

The brown stuff is presumably polymerized oil, AKA "seasoning". At sufficient thickness, it appears black (but blackness is unnecessary for it to be effective as a surface treatment). I don't see any sign of rust in those pictures.




Pictures about "Fighting flash rust on cast iron pans"

Fighting flash rust on cast iron pans - Brown Carriage Wheel
Fighting flash rust on cast iron pans - Close Up Photo of Gray Metal Pipes
Fighting flash rust on cast iron pans - Man Welding Metal Bars



How do you handle flash rust on cast iron?

Flash rusting is normal and can easily be remedied by briskly rubbing vegetable oil with a cloth on the rusting area. Profile rusting can be seen and felt on the cookware. Remove the rust by scrubbing with a soap pad. Once raw cast iron is revealed, re-season the area immediately.

How do you neutralize flash in rust?

If there is flash rusting on a wet object, most of the bright orange rust can be removed by brushing with a soft bristle brush and rinsing with clean water, followed by blotting the surface with lint-free towels and then air drying using fans.

Can you fix rust on cast iron?

Cast-iron skillets are naturally prone to rust. But even if it has turned bright orange, the pot absolutely can be fixed. (Even if you snag an old, rusty skillet at the flea market, that orange will come off!) It only takes a few simple steps to have your rusted cast iron looking brand-new.

Does vinegar remove rust from cast iron?

Mix together equal parts basic white vinegar and water, and either add the solution to the pan if it's rusty only on the inside or completely submerge the pan in a bucket of the stuff to dissolve the rust all over. Letting it soak for about an hour should do the trick, depending on the damage.



Flash Rust on Cast Iron Pans




More answers regarding fighting flash rust on cast iron pans

Answer 2

The other answer is right to point out that recently done seasoning can be brown rather than black. It is still important to make sure it's not rust below a first thin nonblack layer of seasoning. You may want to scratch a little bit off and check the texture, to see if there is rust below the slick surface.

Normally such rusting shouldn't happen, but you wrote that you used a vinegar rinse. Vinegar on unseasoned iron is very likely to result in rust, and even if you didn't notice it before putting it into the oven, the temperature can have enhanced the reaction. So, don't use vinegar on any other acids.

If it should turn out to indeed be flas rust: I have successfully removed it with a strong lye (NaOH in water). Luckily for you, it will strip the new seasoning before it gets to the rust, so you won't have to take multiple steps. After you have cleaned it off, do not neutralize it in any way. Just wash it off with plenty of fresh water, multiple rounds. Then season it. If you see soapy esters emerge when you apply your fat, go back to the washing and drying stage.

Sources: Stack Exchange - This article follows the attribution requirements of Stack Exchange and is licensed under CC BY-SA 3.0.

Images: Milan, Navneet Shanu, SHOCKPhoto by Szoka Sebastian, Pavel Chernonogov