Should sharpening nicked knives with whetstones leave the nicks in the blade?
This question is somewhat similar to How to sharpen knife with chunk missing?, but the knives I have are not ruined like the one in that question, and I doubt the answer here would be to just throw away the knives as in that question.
I have three different Classic Global knives – a G2, a G5, and a GSF22 – which are all somewhere between eight and ten years old. None of them have ever been sharpened before. Especially the G5 and the GSF22 have been frequently used, and the blades are showing the effects of that, so I’ve bought an MS5 ceramic whetstone to sharpen them.
I’m a complete novice when it comes to sharpening knives, especially with whetstones, so I did the usual thing first: watched some YouTube videos (Global have one themselves which was very instructional) and read up on it on the Internet.
The M5-OM whetstone I have is 1000 grit, which I realise is probably not really coarse enough to get efficiently rid of nicks very efficiently, but I didn’t feel like splurging on more than one whetstone to begin with, so I got the medium one to start with.
I’ve just sharpened all three knives now, and I admit the results are a bit underwhelming to me. The knives are decidedly sharper than they were before, but all the little nicks and chips in the blades that have developed over the years are still there – some of them actually look bigger now than they were before, which was rather the opposite of what I wanted to achieve.
For comparison, here are two superimposed images of the blade of the GSF22 before (top) and after (bottom) sharpening (click for full size to see the nicks better):
None of the nicks you see there are very big to begin with (the blade is 11 cm in total), but I would have thought sharpening the knife would at least have reduced them, taking material off the edge of the blade, but not where it’s nicked.
With this level of nicking, is it normal that sharpening the blade does not seem to affect the nick? Or does this level of nicking simply require a coarser grit than 1000 to even start getting rid of the nicks at all? Or is it evident from the photo that I did something very wrong when sharpening (over- or undersharpening, wrong angle, etc.), which may have exacerbated the nicks rather than getting rid of them?
Best Answer
You are indeed supposed to remove so much material from the blade that the nicks disappear completely. You'll have to lose what's probably a least a milimeter of the blade's width.
For that, the 1000er grit is indeed too fine. Go for something much coarser, and use finer grits for finishing. With the stone you're using, you'll have to spend days to get so much steel ground away. Something in the 150-300 range will do nicely for the task you have.
Pictures about "Should sharpening nicked knives with whetstones leave the nicks in the blade?"
Can you ruin a knife with a whetstone?
That said, the technique can be hard to master (as more in-depth explanations of whetstones make very clear). \u201cIt requires a lot of training and one can easily ruin their expensive knife if they improperly sharpen it. It also requires a lot of time.\u201dCan you sharpen a chipped blade?
When tiny bits of the cutting edge actually get chipped off, the only way to fix that is to sharpen the knife by grinding steel away with a coarse whetstone or diamond plate to form a new edge. If you have a large chip, you'll need to remove a lot of steel.Should you push or pull a blade when sharpening?
Apply forces when pushing the knife away while the cutting edge is facing yourself (edge trailing stroke) is recommended. Pulling the knife towards yourself while the cutting edge is facing your side (edge leading stroke) is not recommended because it is generally harder to handle and more dangerous.What should you not do when sharpening a knife?
THE DON'TSDon't run your knife through a knife system or device. Running your blade through a device will unevenly chew up the edge, can scratch the face of the blade, and will not get your knife as sharp as using a whetstone to sharpen.Whetstone Sharpening Mistakes that Most Beginners Make
More answers regarding should sharpening nicked knives with whetstones leave the nicks in the blade?
Answer 2
I recently repaired a global knife with exactly the same kind of nicks. Too small to feel with your fingernail, but definitely felt when cutting paper.
You'll need to re-profile the knife by using a coarse stone (even a brick will do). By holding the knife side perpendicular to the stone surface, and drawing from heel to tip, until the knicks are gone. This will completely dull the knife. Do this until the nicks are gone. Pay attention to the overall shape of the edge (the curve), so that you don't affect the overall geometry of the knife too much, ie, remove materially even across the entire length.
You will then have to re-establish the primary bevel with a coarse stone, and then work up to finer stones in the usual way.
This took me several hours with a 400 grit. In hindsight a brick would have been faster. If you use a whetstone, use the side of the block, rather than the flat face or you will leave deep grooves in the face.
Alternatively, accept the nicks. Use the knives, and sharpen as required. If you don't create new nicks, the use and sharpening will cause them to fade.
Or, you could get them professionally corrected.
Either way, you should think about proper knife care, because they aren't supposed to form nicks like that. Don't cut bones, hard pits, frozen food, and clean carefully under luke warm water. Store safely in a manner where the edge is protected from knocks.
Sources: Stack Exchange - This article follows the attribution requirements of Stack Exchange and is licensed under CC BY-SA 3.0.
Images: Adonyi Gábor, ArtHouse Studio, Marko Garic, Pixabay