Shiny side or not for foil?

Shiny side or not for foil? - Modern taxi cars driving on road with crosswalk

Does it make any difference when you wrap food with aluminum foil for grilling or baking or making a steam pouch whether you put the shiny side in or the shiny side out?

I've seen at least one answer to a questiong about grilling that made mention of this.



Best Answer

I've been told that the shiny side should go on the inside for cooking, and the outside for freezing. In other words, do you want to reflect the heat into the food, or away from the food?

However, common sense (which fails very often) tells me that with the temperature ranges involved, any benefit is marginal, if it exists at all.

The only time it might matter, is if you were trying to warm something up in the sun. Then it might make a difference.

EDIT: From The Straight Dope:

The truth is that the shiny side is not treated with a dangerous chemical. Mineral oil is used as a lubricant during the rolling process, some trace of which may remain on the finished foil--but it's not dangerous. The shiny side is shiny because of the way foil is made. During the last pass through the rolling mill, a double thickness of foil is run between the rollers. The side of each sheet that comes in contact with the polished steel rollers comes out shiny. The other side has a matte finish.

http://www.straightdope.com/columns/read/1135/should-a-baking-potato-be-wrapped-in-foil-shiny-side-in-or-shiny-side-out

ALSO

The official word from the Reynolds aluminum people is as follows: "It makes little difference which side of the Reynolds Wrap aluminum foil you use--both sides do the same fine job of cooking, freezing, and storing food. There is a slight difference in the reflectivity of the two sides, but it is so slight that laboratory instruments are required to measure it."




Pictures about "Shiny side or not for foil?"

Shiny side or not for foil? - From above side view of wistful adult ethnic male taxi driver sitting in bright vehicle and looking away
Shiny side or not for foil? - Adult thoughtful bearded driver in wristwatch and casual clothes driving blue automobile while passing by old building and looking away in daylight
Shiny side or not for foil? - Shiny retro car parked on road near plants under blue sky



Does it matter if you use the shiny side of foil?

Most people think it matters whether aluminum foil is used shiny side up or down, but the surprising truth is that it doesn't make a difference. The variation is a result of the manufacturing process\u2014the shiny side comes in contact with highly polished steel rollers, and the matte side doesn't.

Does it matter which side of foil to use?

"It makes no difference which side of the foil you use unless you're using Reynolds Wrap Non-Stick Aluminum Foil." Non-Stick foil actually has a protective coating on one side, so the company recommends only placing food on the side marked "non-stick" for maximum efficiency.




More answers regarding shiny side or not for foil?

Answer 2

I just cooked 12 baked potatoes; 6 shiny side out, and 6 shiny side in. Each potato was individually wrapped and all potatoes were about the same size. I cooked the shiny side out potatoes first, then turned off the oven and left the oven door open for 30 minutes before cooking the other six. I also unwrapped both sets of potatoes after sitting for five minutes out of the oven, sliced them in half and put butter in between. Both baked at 375°F for an hour timed by the oven; they cooked exactly the same. Neither was more done than the other nor had more crispy skin.

Answer 3

I think with the foil's shiny side outside the food cooks a bit later because it reflects heat away from the food

Answer 4

It takes longer to bake with the shiny side out, I know this because i have cooked for years for large numbers of people and have to do it in about 2 hours max. Shiny side in cooks things faster.

Sources: Stack Exchange - This article follows the attribution requirements of Stack Exchange and is licensed under CC BY-SA 3.0.

Images: Tim Samuel, Tim Samuel, ArtHouse Studio, ArtHouse Studio