Is there a disadvantage to a textured cutting board?

Is there a disadvantage to a textured cutting board? - Cutting board

My new plastic cutting boards have a textured surface. Is this unsanitary?

The textured surface consists of tiny bumps molded into the surface. The pitch of the bumps is about 1mm.



Best Answer

There is another disadvantage to consider with very acute knives (eg sashimi knives, usuba bocho, gyutos sharpened to 12 degrees per side or below) on these kinds of boards: The edge tends to get trapped between the bumps, and instead of camming out, can be bent out of alignment if torque is accidentally applied to the blade (easily happens with rock chopping/walking techniques). Also, you tend to get unclean cuts (similar to a tear-off perforation) at times because the edge bites into the bumps while the food is pushed between them (can happen eg when cutting very elastic foods, like raw dough).

Also, the anti-slip effect from that texture is questionable at best, these boards can be even more slippery on some surfaces - if textured both sides, they can also slide around on your work surface (this is dangerous!) even more than if they were smooth - some mitigation can be achieved by putting towels or paper between the surfaces...




Pictures about "Is there a disadvantage to a textured cutting board?"

Is there a disadvantage to a textured cutting board? - Sliced Cheese on Brown Wooden Chopping Board
Is there a disadvantage to a textured cutting board? - Kitchen Knife
Is there a disadvantage to a textured cutting board? - Variety of Fruits and Vegetables



Quick Answer about "Is there a disadvantage to a textured cutting board?"

Also, the anti-slip effect from that texture is questionable at best, these boards can be even more slippery on some surfaces - if textured both sides, they can also slide around on your work surface (this is dangerous!)

Do you use the rough or smooth side of a cutting board?

The rough surface faces downward to prevent the board from slipping on smooth surfaces.

Why do some cutting boards have grooves?

Cutting Board Juice Grooves Juice grooves are router indentations inlaid 1/2" or 5/8" that follow the outer edge of a cutting board. Grooves serve as a place for any juices, oils, other liquids or loose pieces of food being cut to sit and pool so they don't interfere with the food being cut.

What material should a cutting board is best?

The best cutting board material is one that can be easily cleaned, and doesn't damage or dull knives. Common options for cutting board material are wood, plastic, rubber, and bamboo. Wood cutting boards are superior for their hard-wearing and self-healing properties, and their ability to preserve a knife edge.

Why are wooden cutting boards rough?

It's common for wood grain to slightly raise over time creating a rough surface, especially on boards that haven't been regularly oiled well. Use swirling motions to sand the surface of the board until its silky smooth. Hot dishes fresh off the stove or oven can cause burn marks on cutting boards.



5 Pro Tips for Great Cutting Boards




More answers regarding is there a disadvantage to a textured cutting board?

Answer 2

I read this post and had to comment. cutting boards are usually 2 sided, one side textured the other not textured. the textures side is great for grinding garlic, onions, crushing herbs, holding slippery veggies in place. the flavors from pasting using the back of the blade by running minced garlic or onion across a textured board is amazing.

I'm not saying it replaces my mortar and pestle, but for a quick grind of any herbs is really nice across a good textured board.

Also, filleting and de skinning fish is always done on the textures side. it's too slippery and dangerous using a smooth surface.

The smooth side is all about cutting meat. I don't like using the textured side for meat at all. And the smooth side for sashimi is a must. Doing large volume food prep, it's good to have a textured board on a damp towel for all the veggies and herbs. And a second board that's smooth for meats. the damp towel helps with counter sliding since veggies are on the lighter side and usually require many more chops.

When doing a quick dish, I just use 1 board on a damp towel and do my veggies first, then flip it over and do meats on the smooth side.

Sources: Stack Exchange - This article follows the attribution requirements of Stack Exchange and is licensed under CC BY-SA 3.0.

Images: Kaboompics .com, Karolina Grabowska, Lukas, Lukas